Differences

This shows you the differences between two versions of the page.

--- wlbrdkmtk [2022/07/06 16:18]
steve
+++ wlbrdkmtk [2022/08/22 13:01]
steve Added format chars so git URLs and '--' are shown correctly
@@ Line 9: / Line 9: @@
   - //cd <mtk_dir>//
-  - //repo init -u https://git01.mediatek.com/dtv/mediatek/manifest -b stbrdkm-rel-rdk-i_poc_rdk_c2s//
+  - //repo init -u %%https://git01.mediatek.com/dtv/mediatek/manifest%% -b stbrdkm-rel-rdk-i_poc_rdk_c2s//
-  - //repo sync -c -j `nproc` --no-clone-bundle//
+  - //repo sync -c -j `nproc` %%--no-clone-bundle%%//
   - //repo forall -c 'if [ -e .gitattributes ];then git lfs pull;fi'//
@@ Line 16: / Line 16: @@
   - //cd <rdk_dir>//
-  - //repo init -u https://code.rdkcentral.com/r/manifests -m rdkv-nosrc.xml -b rdkv-2022q1-dunfell//
+  - //repo init -u %%https://code.rdkcentral.com/r/manifests%% -m rdkv-nosrc.xml -b rdkv-2022q1-dunfell//
-  - //repo sync --no-clone-bundle//
+  - //repo sync %%--no-clone-bundle%%//
   -  Copy the meta layer directories from <mtk_dir> into <rdk_dir>
   - //git clone git@github.com:DTVKit/meta-dtvkit-mtk.git//
   - //cd meta-dtvkit-mtk//
-  - //git checkout mtk_20220615//
+  - //git checkout mtk_20220715//
   - //cd ..//
@@ Line 29: / Line 29: @@
   * Select "meta-dtvkit-mtk/conf/machine/dtvkit-whitelabel-dtv.conf", option #37
   * //bitbake lib32-rdk-generic-hybrid-dtv-image//
+== Flashing ==
+When the build has completed successfully, a set of scripts and binary files for installing from USB can be found in a directory called "Target" in "<rdk_dir>/build-dtvkit-whitelabel-dtv/tmp/deploy/images/dtvkit-whitelabel-dtv/MTKIMG/usb_update". The whole "Target" directory needs to be copied to a FAT, FAT32 or vfat formatted USB memory stick that has at least 1GB of free space. Copy the "Target" directory to this device such that "Target" is in the top-level directory. The device must also be writeable when the image is installed.
+Now proceed with the following steps:
+  * Connect the serial adapter to the STB as shown here:
+{{ :whitelabel_serial.jpg?direct&200 |}}
+  * Use a serial communication program to connect to the serial and use the following settings: 115200 bps, 8 data bits, 1 stop bit, no parity, no hardware flow control.
+  * Power on the STB and within the first 3 seconds press any key (e.g. spacebar) to interrupt the boot process. You should now be at the a command prompt showing: “//MT5221#//”
+  * Insert the USB stick into either of the 2 USB ports on the side of the STB.
+    * If the USB stick is inserted into the USB towards the front of the STB, enter //usb start 2// at the command prompt.
+    * If the USB stick is inserted into the USB towards the rear of the STB, enter //usb start 0// at the command prompt.
+    * Completion of either of the above commands should result in “1 Storage Device(s) found” being shown on the console.
+  * To start the update, enter //udstar// at the command prompt.
+  * The update will take less than 2 minutes after which the box will boot into the newly installed image.

DTVKit Wiki

User Tools

Site Tools

Differences

Page Tools